Surfface treatment (acc. EN 10088-2)
Thickness:
0,20 – 3,00 mm – for tape
0,50 – 6,00 mm – for sheets, depending on machining
Width:
max. 700 mm – for tape
max. 1500 mm – for sheets
Length:
Length accordingly max. RAD 2000 mm – for tape material
max. 4500 mm for sheet material – upon request even longer
Surface treatment:
one- and two sided– for tape as well as sheets
Grinding:
Grain 80 to 400 – upon request differing grain sizes are possible.
All ground surfaces can be foil covered.
Brushed:
All brushed surfaces can be foil covered.
Other design possibilities:
Apart from the above mentioned design possibilities it is also possible to use other finishes for the surfaces, i.e.:
-
Polished surface
-
Duplex grind/ Micro grind (grinding and brushing)
-
Special grind according to a sample
- Refinishing
Tolerances:
We always produce according to DIN EN ISO 9445, whereby smaller tolerances and limited demands (i.e. analysis limits) which exceed the guidelines of the standards, can be agreed upon.
Surface protection
As high quality rustproof steel has an ever increasing aesthetic demand on the surface, most of our products can be covered with a protecting foil if requested.
An overview of the foils we use can be seen directly in the PDF.
It goes without saying that apart from the above mentioned protection foils other foils can also be supplied, please ask our employees about our range.
Edge finishing
The multifaceted application range of our products demands not only the customary edge finishing but also special edge finishing according to the customers special demands.
We can provide special edgings which are in accordance with the specific customer requirements.
Edge finishing:
-
Cut edge (GK) – groove less upon request
-
deburred/ sharp (sharp edged)
-
rounded off edge (semi-round)
-
chase thread edge (round)
- planed edge (sharp edged)
other edge finishing possibilities:
Apart from the above mentioned edge finishes it is also possible to supply the following product finishing:
-
flat rolled surfaces – – to optimise the surface evenness
- lightly re-rolled surfaces – to increase the tensile strength
Tolerances:
We always produce according to DIN EN ISO 9445, whereby smaller tolerances and limited demands (i.e. analysis limits) which exceed the guidelines of the standards, can be agreed upon
Commission pocessing
If bottleneck situations arise in your company, use the possibilities we offer to ensure your on-time- delivery.
Slitting work:
Thickness: 0, 10 – 8, 00 mm – upon request also thicker or thinner
Width: 3, 00 – 1500 mm – according to band thickness
Inner ring diameter: 300/ 400/ 508 und 610 mm
Outer ring diameter: max. 2000 mm
Ring weights: from about 0, 5 kg/mm BB – upon request also lower
Edge finishing: according to our delivery specifications
Tolerances: DIN EN ISO 9445 – whereby smaller tolerances are possible upon request.
Cross cut work:
Thickness: 0,30 – 8,00 mm – upon request also thicker or thinner
Width: from 10 – 1500 mm – upon request also thinner or wider
Length: from 50 – 8500 mm – upon request also shorter or longer
Inner ring diameter: 300/ 400/ 508 und 610 mm
Outer ring diameter: max. 2000 mm
Edge finishing: cut edges – further edge finishing upon request
Tolerances: DIN EN ISO 9445 – whereby smaller tolerances are possible upon request.
Circling/ -stamping work:
Thickness: 0,30 – 8,00 mm – upon request also thicker or thinner
maximum diameter: 1250 mm – Depending on the material thickness
minimum diameter: 125 mm – Depending on the material thickness
Edge finishing: cut edges
Tolerances: DIN EN ISO 9445 – whereby smaller tolerances are possible upon request.
Product range
Product range slit strip
Thickness |
0,10 – 8,00 mm
(upon request also thicker or thinner) |
Width |
3,00 – 2000 mm – je nach Banddicke |
Inner ring diameter |
300/ 400/ 508 und 610 mm |
Outer ring diameter |
max. 2000 mm |
Ring weights |
ab ca. 0,5 kg/mm BB (upon request also smaller) |
Product range sheets and pre-cut parts
Thickness | 0,10 – 8,00 mm
(upon request also thicker or thinner) |
Dimensions | Small dimensions – KF 1000 x 2000 mm Middle dimensions – MF 1250 x 2500 mm large dimensions – GF 1500 x 3000 mm |
Other dimensions | 1000 x 1000 – 3000 mm or similar 1250 x 1000 – 3000 mm or similar 1500 x 1000 – 3000 mm or similar 2000 x 1000 – 3000 mm or similar |
Finished cut parts in widths from 10 – 2000 mm
upon request also thicker or thinner
in lengths from 10 – 8500 mm
upon request also shorter or longer
Product range Profiles
Thickness | 0,30 – 4,00 mm |
Profile height | max. 125 mm |
Profile width | max. 700 mm |
Profile length | 100 – 9000 mm |
Profile shape | according to your specifications |
Product range Pipes
Wall thickness | 0,50 – 2,00 mm -upon request also thicker or thinner |
Diameter | 12 – 60 mm -upon request also small or larger |
Shapes |
Round pipes/ square pipes/ rectangular pipes/ flat oval pipes / oval pipes |
Lengths | Trade lengths – upon request cut to fixed length |
Our detailed product range can also be easily downloaded and printed out.
Product range sheets and pre-cut parts
Product range surface protection
Product range surface treatment
Product range pipes and profiles
Product range commission work
Dieser Beitrag ist auch verfügbar auf: German